EMT Practice Test

1. Question Content...

---

Question1: Click the exhibit.

Referring to the exhibit, traffic handled by the s-1 scheduler is out of profile.
Assuming bandwidth is available in this scenario, which statement is correct?

Question2: Click the Exhibit.

Router1, in peer AS 65001, advertises routes to R2 using EBGP. R2 advertises the routes learned from R1 to R3 using IBGP. R3 is configured as a route reflector with routers R6 and R7 as clients.
Referring to the exhibit, to which routers will R3 advertise the BGP routes received from R2?

Question3: Click the Exhibit.




You are configuring a new BGP session between router1 and router2. The session does not establish.
Referring to the exhibit, what must be done to establish this session?

Question4: Which router ID is correct for OSFPv3?

Question5: Click the Exhibit.

You are troubleshooting an OSPF adjacency issue between R1 and R2.
What is the reason for the ExStart state shown in the exhibit?

Question6: Click the Exhibit.

You have deployed sparce-mode multicast in your network using the IGP metrics shown in the exhibit.
Which path will (*, G) traffic follow form the source to the receiver before the (S, G) state is registered?

Question7: Click the Exhibit.

You are configuring dynamic rendezvous points for your PIM multicast domain. You have chosen to use auto-RP as the dynamic RP mechanism. You are not seeing the auto-RP announcements.
Referring to the exhibit, which two configurations will solve this problem? (Choose two.)

Question8: Click the Exhibit.

Router R1, in peer AS 65001, advertises routes to R2 using EBGP. R2 advertises the routes learned from R1 to R3 using IBGP.
Referring to the exhibit, to which routers will R3 advertise the BGP routes received from R2?

Question9: Click the Exhibit.

You are configuring MSTP to prevent loops in your Layer 2 network. After applying the configuration, you notice that MSTO is not working correctly.
Referring to the exhibit, what is causing the problem?

Question10: Click the Exhibit.

Referring to the exhibit, you are receiving multiple routes from ISP3 through two EBGP neighbors. You must ensure that all traffic leaving R1 destined to the networks advertised by ISP3 go through ISP2.
What should you do on R1 to accomplish this task?

Question11: Which two statements are true about OSPFv3? (Choose two.)

Question12: Which two statements are true about PIM source-specific multicast (SSM)? (Choose two.)

Question13: Click the Exhibit.


Referring to the exhibit, which set of interfaces will be registered by MVRP?

Question14: What allows non-Web enabled devices to access the network on a port configured for captive portal?

Question15: A new PoE+VoIP handset was added to an EX Series device. The handset is experiencing connectivity issues. The EX Series device's committed configuration includes the set poe interface all telemetry command. You look at the telemetry log in the device to review power consumption and you notice entries have not been occurring for days.
What would cause telemetry logging to stop?

Question16: Your network provider supports multicast traffic but your provider network does not. You want to allow multicast hosts outside of your network to receive multicast traffic sourced within your network.
How would you satisfy this requirement?

Question17: You are enabling 802.1X authentication on an EX Series device. You are configuring the switch in the conference room where you will have non-employees with devices that do not support 802.1X authentication connecting to your network. You must ensure that these users can connect to your network but are restricted to Internet access only.
What should you do to accomplish this task?

Question18: Click the Exhibit.

A customer on MSTI-2 was isolated due to a physical link outage on Switch 5's ge-0/0/32 interface.
Referring to the exhibit, which corrective action would solve this problem?

Question19: Which protocol is used for port-level access control and authentication?

Question20: Click the Exhibit.

Which AS path matches the AS path regular expression shown in the exhibit?

Question21: Click the Exhibit.

Referring to the exhibit, which statement is true?

Question22: Click the Exhibit.


Referring to the exhibit, Area 1 is a stub area.
Which two statements are correct in this scenario? (Choose two.)

Question23: Which protocol is a multicast routing protocol?

Question24: OSFP is stuck in the ExStart state.
What is a common cause of this problem?

Question25: Click the Exhibit.

A customer is concerned that the route damping policy on routes with prefixes greater than/17 is allowing too many flaps to occur. The customer does not want to change the default timer.
Referring to the exhibit, which two actions would allow fewer flaps per route? (Choose two.)

Question26: You are configuring a scheduler map on an EX9200 Series device. You want to ensure that traffic is dropped in a policing action once traffic exceeds the configured transit rate.
Which configuration parameter will meet this requirement?

Question27: Which three statements are true about strict-high priority queues? (Choose three.)

Question28: When configuring class of service, what would you use to allocate bandwidth to a forwarding class?

Question29: Click the Exhibit.

Referring to the exhibit, which two statements are correct? (Choose two.)

Question30: Which type of BGP is used to peer with a different autonomous system?

Question31: Click the Exhibit.

Referring to the exhibit, you have EBGP peerings with both ISP1 and ISP2. You are receiving the
172.25.12.0/24, 172.25.13.0/24, 172.25.14.0/24, and 172.25.15.0/24 routes through both neighbors. You must ensure that traffic to these prefixes are load balances through both service providers. You have configured a load-balancing policy and have applied it to the forwarding table, but the prefixes are not being load balanced.
What is required to accomplish this task?

Question32: Click the Exhibit.


Referring to the exhibit which two statements are true? (Choose two.)

Question33: Which two statements are true about 802.1Z dynamic filters based on RADUIS attributes? (Choose two.)

Question34: Your campus EX9200 core devices are highly oversubscribed on bandwidth ans reporting massive dropped packets. To immediately address the issue, you decide to implement shaping on all interfaces.
Which action will accomplish?

Question35: Click the Exhibit.

You have three switches, each with a trunk connection allowing all VLANs to the switches. CIST will coverage, however MSTP will not.
Referring to the exhibit, which statement is correct?

Question36: Computers on the network are assigned IP addresses from DHCP server based on the MAC address of the computer. The network administrator wants computes assigned to a VLAN using the computer's IP addresses, regardless of where the computers are plugged into the network.
In this scenario, which two statements are true? (Choose two.)

Question37: Click the Exhibit.

Referring to the exhibit, what is the minimum number of MSTP regions where the topology would be implemented?

Question38: Click the Exhibit.

You are asked to advertise the 1.0.0.0/8 and 1.5.5.5/32 routes to your 10.254.32.2 BGP peer.
Referring to the exhibit, which configuration change would satisfy this requirement?

Question39: Click the Exhibit.

All of the clients attached to your EX4300 report that authentication to the network is abnormally slow.
While troubleshooting, you individually test the RADIUS servers used for authentication and receive the information shown in the exhibit.
What happened to the RADIUS server 172.28.30.95?